background image

19

ENGLISH

ENGLISH

Fig. 27

5.2.4. T E R M I N A L

BLOCK J5 (high
voltage)

Terminal block for motor
connection.
Connect the wires to the
terminals of J5 as shown
in Fig.26.

B

L A C K

 

A N D

  B

R O W N

 

W I R E S

  =

electric motor supply
phases

B

LUE

 

WIRE

= electric motor

common

5.2.5. CONNECTOR  J6 (high voltage)

Connector for quick connection of the capacitor.

5.2.6. TERMINAL BLOCK  J7 (high voltage)

230V~ terminal block for connection of the flashing light (max
60W).

5.2.7. TERMINAL BLOCK  J8 (high voltage)

Terminal block for connection of the 230V~ 50Hz power supply
(L=Line    N=Neutral)
Connect the earth wire to the operator as shown in Fig.27.

5.2.8.

INDICATOR LEDS

5 LEDs on the board indicate the status of the terminal inputs
(see Table 4 and fig.28):

L

ED

 

ON

  = contact closed

L

ED

 

OFF

   = contact open

TABLE  4

MEANING OF STATUS INDICATOR LED

S

LED

ON

OFF

OPEN

Command active

Command not active

STOP

Command not active

Command active

FSW

Safeties disengaged

Safeties engaged

FCC

Closing limit disengaged

Closing limit engaged

FCA

Opening limit disengaged

Opening limit engaged

Fig. 25

Fig. 24

5.3.

INSTALLING ELECTRIC LOCK

Since the gear motor allows the gate to be moved manually
when the motor is not running, an electric lock must be
installed to ensure that the gate remains locked when closed.
It must be positioned vertically on the upper guide upright (if
the height of the gate permits) to allow it to be released from
both inside and outside (fig.29).

Fig. 28

Closure

Fig. 29

Upper guide

upright

Electric lock

Post

Lock plate

Fig. 31

J4

J3

CH-DX

CH-SX

844MPSR

J5

J4

J3

CH-DX

CH-SX

844MPSR

J5

M

J5

Fig. 26

J2

1     2     3     4     5     6     7     8     9

BROWN

BLACK

BLUE

Fig. 26

Summary of Contents for 844 MC-R













Reviews: