FOX 500 Tx/Rx • Remote Control
Remote Control, cont’d
4-4
FOX 500 Tx/Rx • Remote Control
4-5
]
= CR/LF (carriage return/line feed) (0x0D 0A)
•
= space
X!
= Mute/auto image/front panel lock status
0 or 1 (0=off and 1=on)
X@
= Output sync format
0 = RGBHV
1 = RGsB
X#
= Output sync polarity
0 = follow input
1 = force sync to negative
X$
= Horizontal and vertical position
X%
= Horizontal start
0 to 255
X^
= Pixel phase
0 to 31
X&
= Total pixels
± 255 of the default value
X*
= Sync frequency
xxx.xx (frequency in kHz [H]
or Hz [V])
X(
= Memory preset number
1 to 30
X1)
= Audio gain adjustment range
0 to 10
X1!
= Audio attenuation adjustment range
0 to -18
X1@
= Audio level adjustment range
-18 to +10 (in 1.0 dB steps)
X1#
= Output level
0 = consumer
1 = professional
X1$
= Test pattern
0 = none
1 = Color Bars
2 = grayscale
3 = alternating pixels
X1%
= Firmware version
v
.
vv
X1^
= Link/input status
0 = link or input not sensed
1 = link or input sensed
X1&
= Mode
SM = singlemode
MM = multimode
X1*
= Transmitter or receiver
Tx = transmitter
Rx = receiver
Unit-initiated messages
When a local event, such as a front panel operation or error
condition, occurs, the unit responds by sending a message to the
host. The unit-initiated messages are listed below:
(c) COPYRIGHT 2006, EXTRON ELECTRONICS FOX 500 Tx,
V
x
.
xx
,
,
60-
xxx
-
xx
]]
- or -
(c) COPYRIGHT 2006, EXTRON ELECTRONICS FOX 500 Rx,
V
x
.
xx
,
,
60-
xxx
-
xx
]]
The connected unit issues the appropriate copyright message
(above) when it first powers on. V
x
.
xx
is the firmware version
number, 60-
xxx
-
xx
is the connected unit's part number.
Reconfig
]
The unit sends the Reconfig message whenever the video input
signal to the transmitter is changed.
Hph
X$]
The unit sends the Hph message whenever the output's
horizontal position is shifted.
Vph
X$]
The unit sends the Vph message whenever the output's vertical
position is shifted.
Hst
X%]
The unit sends the Hst message whenever the output's
horizontal start is shifted.
Tpx
X&]
The unit sends the Tpx message whenever the total pixels
variable is changed.
Phs
X^]
The unit sends the Phs message whenever the pixel phase
variable is changed.
Syn
X#]
The unit sends the Syn message whenever the output video
format is changed.
Pol
X#]
The unit sends the Pol message whenever the output sync
polarity setting is changed.
Aud
X1@]
The unit sends the Aud message whenever the input audio level
(gain and attenuation) is changed.
Amt
X!]
The unit sends the Amt message whenever audio output is
muted or unmuted.
Lvl
X1#]
The unit sends the Lvl message whenever the audio output level
is changed.
Spr
X(]
The unit sends the Spr message whenever a preset is saved.
Rpr
X1#]
The unit sends the Rpr message whenever a preset is recalled.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
