manualshive.com logo in svg

Extron electronics FOX 500 Rx, User Manual

Share
Download
Extron electronics FOX 500 Rx User Manual Download Page 23

FOX 500 Tx/Rx • Operation

Operation, cont’d

3-12

FOX 500 Tx/Rx

4

Chapter 4

Remote Control

Rear.Panel.Remote.RS-232.Ports

Front.Panel.Configuration.Port

Simple.Instruction.Set.Control

Windows

®

-Based.Program.Control

Front panel security lockout (executive mode)

The front panel security lockout limits the operation of the 

receiver from the front panel.  When the receiver is locked, the 

Menu and Next buttons are disabled.
To toggle the lock on and off, press and hold the Menu button 

and the Next button for approximately two seconds (figure 3-9).

MENU

NEXT

MENU

NEXT

Exe Mode

Disabled

Exe Mode

Enabled

Press and 

hold the Menu and Next 

buttons simultaneously to toggle the 
front panel lock on or off.

2 seconds

Release the

Menu and Next

buttons.

The LCD indicates 
the front panel lock 
(enabled or disabled).

Figure 3-9 — Toggle front panel lock on or off

If the user pushes either button when the receiver is locked, the 

LCD displays Exe Mode Enabled.

im Vertrieb von

            CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Summary of Contents for FOX 500 Rx









































Reviews:

No comments

Brands by name

Popular brands

Load more brands