Extron electronics CrossPoint 300 124 User Manual Download Page 19 | Manualshive

Page: 19 / 96

background image

2-5

CrossPoint 300 Matrix Switchers • Installation

4

Connections for balanced and unbalanced audio outputs —

These 3.5 mm,

5-pole captive screw connectors output the selected unamplified, line level
audio. Connect audio devices, such as an audio amplifier or powered
speakers. See figure 2-5 to properly wire an output connector.

Unbalanced Output

Tip

See caution

Sleeve

Tip

See caution

Balanced Output

Tip

Ring

Sleeve (s)

Tip

Ring

Figure 2-5 — Captive screw connector wiring for audio output

CAUTION

Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative
(-) terminal will damage the audio output circuits.

The volume level for each output can be individually set via the front panel or
RS-232/RS-422 control. See chapter 3, Operation, chapter 4, Programmer’s
Guide, and chapter 5, Switcher Software, for details.

RS-232/RS-422

5

RS-232/RS-422 connector —

Connect a host device, such as a computer, touch

panel control, or RS-232 capable PDA to the switcher via this 9-pin D
connector for serial RS-232/RS-422 control (figure 2-6).

RS-232 Function

Pin

RS-422 Function

1
2
3
4
5
6
7
8
9

—

TX

RX

—

Gnd

—
—
—
—

Not used
Transmit data
Receive data
Not used
Signal ground
Not used
Not used
Not used
Not used

—

TX–

RX–

—

Gnd

—

RX+

TX+

—

Not used
Transmit data (–)
Receive data (–)
Not used
Signal ground
Not used
Receive data (+)
Transmit data (+)
Not used

5

1

9

6

RS232/RS422

REMO

TE

Figure 2-6 — RS-232/RS-422 connector

See chapter 4, Programmer’s Guide, for definitions of the SIS commands (serial
commands that you can use to control the switcher via this connector) and
chapter 5, Matrix Software for details on how to install and use the control
software.

The switcher can support either RS-232 or RS-422 serial communication
protocol, and operate at 9600, 19200, 38400, or 115200 baud rates.
See Selecting the RS-232/RS-422 protocol and baud rate in chapter 3,
Operation, to configure the RS-232/RS-422 port from the front panel.

If desired, connect an MCP 1000 remote control panel master unit to the
switcher’s RS-232/RS-422 connector. You can also connect an MKP 1000
remote keypad or MCP 1000 slave unit to the MCP 1000 master unit. Refer to
the MCP 1000 Remote Control Panel User’s Manual and the MKP 1000 User’s
Manual for details.

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

«
...
17
18
19
20
21
...
»

Summary of Contents for CrossPoint 300 124

































































































Reviews:

No comments

Related manuals for CrossPoint 300 124

Brand: Kathrein Pages: 8

Brand: Nayar Systems Pages: 21

Brand: Kathrein Pages: 24

Brand: Kasia Pages: 5

Brand: Maipu Pages: 21

Brand: Maico Pages: 56

Brand: CYP Pages: 32

Brand: Hama Pages: 10

Brand: StarTech.com Pages: 2

CT.TS005.003902

Brand: Talkswitch Pages: 309

LiteWave LS105G

Brand: TP-Link Pages: 3

Brand: Quidway Pages: 43

Brand: Lindy Pages: 12

S-Mix-Pro 18*18

Brand: Kensence Pages: 24

Brand: Black Box Pages: 2

Brand: Conrad Pages: 8

Brand: InvoTek Pages: 4

Brand: Novus Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands