Extreme Networks Summit Summit24 Installation And User Manual Download Page 160 | Manualshive

Page: 160 / 244

background image

160

Summit24e3 Switch Installation and User Guide

Spanning Tree Protocol (STP)

A port can belong to only one STPD. If a port is a member of multiple VLANs, then all those VLANs
must belong to the same STPD.

The key points to remember when configuring VLANs and STP are:

•

Each VLAN forms an independent broadcast domain

•

STP blocks paths to create a loop-free environment

•

When STP blocks a path, no data can be transmitted or received on the blocked port

•

Within any given STPD, all VLANs belonging to it use the same spanning tree

NOTE

Ensure that multiple STPD instances within a single switch do not see each other in the same
broadcast domain. This could happen if, for example, another external bridge is used to connect VLANs
belonging to separate STPDs.

If you delete an STPD, the VLANs that were members of that STPD are also deleted. You must remove
all VLANs associated with the STP before deleting the STPD.

Defaults

The default device configuration contains a single STPD called s0. The default VLAN is a member of
STPD s0.

All STP parameters default to the IEEE 802.1D values, as appropriate.

STPD BPDU Tunneling

You can configure ExtremeWare to allow a BDPU to traverse a VLAN without being processed by STP,
even if STP is enabled on the port. This is known as BPDU tunneling.

To enable and disable BPDU tunneling on a VLAN, use the following command:

[enable | disable] ignore-bpdu vlan <name>

If you have a known topology and have switches outside of your network within your STPD, use this
feature to keep the root bridge within your network.

STP Configurations

When you assign VLANs to an STPD, pay careful attention to the STP configuration and its effect on
the forwarding of VLAN traffic.

Figure 26 illustrates a network that uses VLAN tagging for trunk connections. The following four
VLANs have been defined:

•

Sales is defined on switch A, switch B, and switch M.

•

Personnel is defined on switch A, switch B, and switch M.

•

Manufacturing is defined on switch Y, switch Z, and switch M.

•

Engineering is defined on switch Y, switch Z, and switch M.

«
...
158
159
160
161
162
...
»

Summary of Contents for Summit Summit24





















































































































































































































































Reviews:

No comments

Related manuals for Summit Summit24

RackSwitch G8264

Brand: IBM Pages: 20

Flex System FC3171

Brand: IBM Pages: 64

Brand: Ribimex Pages: 15

Brand: Manhattan Pages: 2

3CB9E7 - CoreBuilder 9000 Chassis Switch

Brand: 3Com Pages: 132

Brand: Cabletron Systems Pages: 54

Brand: TESmart Pages: 4

Brand: TCi Pages: 11

Brand: Kramer Pages: 4

Lanolinx LNX-1002GN

Brand: ANTAIRA Pages: 110

Brand: Lindy Pages: 16

Brand: GoMax Electronics Pages: 6

Brand: Clever Little Box Pages: 12

3C17205-US - Corp SUPERSTACK 3 SWITCH 4400...

Brand: 3Com Pages: 153

OTM3200E4230C-GE

Brand: ABB Pages: 24

Brand: Comelit Pages: 7

Brand: Zamel Pages: 2

Brand: CYP Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands