manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560i, Installation Manual, Page: 37 / 46

Share
Download
Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 37

3. Attach both the cable clamps to the WS-MBO-POLE01 bracket.

Open the cable clamp by turning a flat bladed screwdriver counterclockwise. Then insert the non-
clamp end into the pole bracket through the holes.

4. Put the metal band around the pole and attach the WS-MBO-POLE01 bracket to the pole.

5. Tighten the cable clamp screw clockwise, tightening the band around the pole.

Figure 11: Tightening the cable clamps on the POLE01 bracket

Install the Plastic Service Panel on the Access Point

About This Task

A service panel is used to protect the access point glands from damage. A service panel must be
installed when:

•

The access point is installed with an under-seat enclosure.

•

The access point is installed with the ART02 articulating mounting bracket with more than 20
degrees tilt.

Install the Access Point

Install the Plastic Service Panel on the Access Point

ExtremeWireless™ AP560i Access Point

37

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments