manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560i, Installation Manual, Page: 29 / 46

Share
Download
Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 29

Install the Access Point on a Pole

Before You Begin

The access point is used with the KT-147407-02 bracket parts and KT-150173-01 extension arm for pole
installation. The access point is mounted on a pole by attaching:

1.

All three parts of the KT-147407-02 bracket.

2.

The KT-150173-01 extension arm with all the KT-147407-02 bracket parts.

3.

The pole bracket part of the KT-147407-02 bracket.

4.

The KT-150173-01 extension arm with the pole part of the KT-147407-02 bracket.

The following hardware is required to install the AP560i access point on a pole:

•

Flat part of the KT-147407-02 bracket

•

Pole part of the KT-147407-02 bracket

•

1-axis tilt bracket

•

Six M6 screws

•

Two hex-head M12 stainless-steel screws

•

Two hex-heads M12 stainless-steel nuts

•

Two M12 screws

•

Two M12 hex nuts

•

0.5 in. wide stainless-steel cable clamps

•

KT-150173-01 extension arm

Note
You must provide M6 hex-head screws and screw-in anchors.

Install the Access Point on a Pole Using KT-147407-02 Bracket Parts

Before You Begin

The following hardware is required for pole installation using KT-147407-02 bracket parts:

•

Flat part of the KT-147407-02 bracket

•

1-axis tilt part of the KT-147407-02 bracket

•

Pole part of the KT-147407-02 bracket

•

Four M6 screws

•

Two hex-head M12 stainless-steel screws

•

Two hex-head M12 stainless-steel nuts

•

Two 0.5 in. wide stainless-steel cable clamps

•

One access point

Install the Access Point

Install the Access Point on a Pole

ExtremeWireless™ AP560i Access Point

29

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments