manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560i, Installation Manual, Page: 27 / 46

Share
Download
Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 27

Install the Access Point Using MBO-ART02 Articulating Mounting Bracket

About This Task

Table 11: Hardware requirements for MBO-ART02 articulating mounting bracket wall
installation

Quantity

Item

1

Access point

1

MBO-ART02 articulating mounting bracket

6

M6 hex-head screws

Two M6 hex-head screws to attach the MBO-ART02 to the access

point.

Four M6 hex-head screws to attach the MBO-ART02 bracket to the

wall.

Note
When using the MBO-ART02 articulating mounting bracket, set the minimum downward tilt
to less than 20 degrees to prevent water ingress. If you keep the tilt to more than 20 degrees,
a service panel (EIO-03-SP) must be installed to protect the glands on the access point.

For installation instructions on how to install the service panel, see 

Install the Plastic Service Panel on

the Access Point

 on page 37.

To install the access point on a wall:

Install the Access Point

Install the Access Point Using MBO-ART02 Articulating

Mounting Bracket

ExtremeWireless™ AP560i Access Point

27

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments