manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560i, Installation Manual, Page: 19 / 46

Share
Download
Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 19

3. Place the metal sloping bracket, attach the nuts and washers to the exposed threads, and torque

them to 60 in-lbs.

About This Task

Attach the conduit cable through the conduit holes on the metal sloping bracket, then attach the metal
L bracket to the access point, and install the access point on a slope.

Procedure

1. Attach the conduit couplers to the conduit.
2. Remove the locking nut.

For the conduit hole that is not used, insert a blank conduit cover over the conduit hole in the slope.

Figure 2: Metal sloping bracket conduit holes

Callout

Description

1

Conduit holes on either sides of the metal sloping bracket

2

Conduit cable holes in the slope

3. If you are using the left side conduit hole on the metal sloping bracket, attach the correct size

conduit cover to the conduit hole.

4. Tighten the locking nut.
5. If you are using the conduit hole in the slope, attach the conduit coupler and the locking nut directly

to the slope conduit hole.

Note
The conduit must be 1 in. in diameter to attach the conduit coupler and the nut directly in
the slope.

6. If you are using the right side conduit hole in the slope, repeat 

step 3

.

Install the Access Point

Install the EIO-04 Under-Seat Enclosure and the Access

Point on a Slope

ExtremeWireless™ AP560i Access Point

19

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments