Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 18 | Manualshive

Page: 18 / 46

Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 18

Related Topics

AP560i Purchase Order Information

Install the Access Point Under-Seat

About This Task

The AP560i is used with the EIO-03 or EIO-04 mounting kit during the under-seat installation
procedure.

The EIO-03 or EIO-04 under-seat mounting kit can be installed on a:

Procedure

1. Slope
2. Flat surface such as a stadium floor
3. Riser, with EIO-02 silicone rubber kit

Note
The best practice is to install the EIO-03 under-seat mounting kit horizontally. The EIO-03
under-seat mounting kit can be installed vertically on a slope, a flat surface or stadium
riser.

Install the EIO-04 Under-Seat Enclosure and the Access Point on a Slope

Install the EIO-04 under seat enclosure with the AP560i access point on a stadium slope.

Before You Begin

Table 9: Hardware requirements for slope installation

Item quantity

Description

1

AP560i access point

6

10 mm M6 screws with integral washers

4

75 mm service panel shoulder screws

2

Anchor posts

2

Flat washers for anchors

2

Lock washers for anchors

1

Metal "L" bracket

1

Plastic service panel base

1

Plastic service panel top with captive screw

1

Metal sloping bracket

Attach the metal sloping bracket on a slope:

1. Using the metal sloping bracket as a template, mark and drill two holes in the concrete.
2. Insert the anchors without the nuts and washers.

Install the Access Point Under-Seat

Install the Access Point

18

ExtremeWireless™ AP560i Access Point

«
...
16
17
18
19
20
...
»

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments