background image

 

2

                                             

PRC20-EU-EN-V1.2   1/13 

Introduction 

 

Thank you for selecting the Extech Model PRC20. This device is shipped fully tested and calibrated 
and, with proper use, will provide years of reliable service. Please visit the Extech Instruments 
website (www.extech.com) to check for the latest version of this User Guide. Extech Instruments is 
an ISO-9001 certified company. 
 

Safety 

 

International Safety Symbols 

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the 
manual for further information. 
 
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages 
may be present 
 
Double insulation 
 

Safety Notes 

 

Turn the unit OFF when the device is not in use. 

 

Remove the batteries if the device is to be stored for longer than 60 days.

 

 

Never dispose of batteries in a fire. Batteries may explode or leak.

 

 

Never mix battery types. Always install new batteries of the same type.

 

Cautions 

 

Improper use of this meter can cause damage, shock, injury or death. Read and understand 
this user manual before operating the meter. 

 

Inspect the condition of the thermocouples and the meter itself for any damage before 
operating the meter. Repair or replace any damage before use. 

 

If the equipment is used in a manner not specified by the manufacturer, the protection provided 
by the equipment may be impaired. 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for prc20











Reviews: