background image

 

9

                                             

PRC20-EU-EN-V1.2   1/13 

Tilt Stand / Hanger 

 

The rear stand is provides two methods for convenience in viewing.  

1. Pull the bottom portion of the stand out to place the unit on a flat surface for viewing. 
2. Pull the bottom and top portions of the stand out, and then rotate the stand to allow the unit 

to be hung. 

 

Battery Replacement 

 

When the battery icon appears on the display, the six AA batteries must be replaced. 
The battery compartment is located on the rear of the meter. 
 

1. Open the tilt stand, loosen the captive Philips head screw and remove the battery cover. 
2. Remove and replace the batteries, observing polarity. 
3. Replace and secure the battery cover. 

 

All EU users are legally bound by the Battery Ordinance to return all used batteries to 
community collection points or wherever batteries / accumulators are sold. 
Disposal in household trash or refuse is prohibited. 

Disposal: 

Follow the valid legal stipulations in respect of the disposal of the device at the 

end of its lifecycle 

 

Battery Safety Reminders 

  Please dispose of batteries responsibly; always observe local, state, and federal regulations 

with regard to battery disposal. 

  Never dispose of batteries in a fire. Batteries may explode or leak. 

  Never mix battery types or old and new batteries. Always install new batteries of the same 

type.

 

 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for prc20











Reviews: