background image

Disposal

Electrical and electronic equipment (EEE) often contain materials, components and substances 

that may harm the environment or be hazardous to your health. Products (WEEE) marked with 

the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at 

the end of its life. Though legislation may differ from country to country we strongly advise 

that electrical and electronic waste is separated from other waste and disposed of according to 

national legislation to protect the environment and personnel that may come into contact with 

waste.

How to use this manual

This manual has been prepared based on the specific product and

contains relevant technical information and installations guides.

Accessories and spare parts are not covered by this manual. 

Please refer to the individual manuals of these components.

This installation manual does not contain any system design documentation.

Failure to observe instructions marked with a danger symbol 

may result in personal injury and/or damage to the product.

Errors and omissions excepted.

Symbols

The following symbols may be used in the manual 

to draw attention to danger or risk of personal 

injury or damage to the product.

General prohibition

Failure to observe instructions marked with the prohibited 

symbol may result in extreme danger or serious personal injury.

General warning

Failure to observe instructions marked with a danger symbol 

may result in personal injury and/or damage to the product.

General attention

Marks a dangerous situation that, in the worst-case scenario, 

can cause serious personal injury or significant damage to the product.

Electricity hazard/High Voltage

Marks a situation in which caution is advised due to the risk of high voltage electric 

shock which can cause serious personal injury or significant damage to the product.

Connect an earth terminal to the ground

Failure to observe instructions marked with a danger symbol 

may result in personal injury and/or damage to the product.

Permitted and approved

Permitted and approved method of installation.

Prohibited and not approved 

Prohibited and not approved method of installation.

Summary of Contents for EFC18

















Reviews: