EXFO Burleigh Wavemeter WA-1100 Operating Manual Download

Page: 10 / 67

WA-1100/WA-1600 Wavemeter Operating Manual

1 Introduction

08115-M-00 Rev E

1-5

Fan Filter Cleaning

The fan on the rear panel of the WA-1100/1600 provides important ventilation to
components inside the chassis. A filter covers the fan opening to keep out dust. This
filter should be cleaned periodically, especially if it becomes noticeably dirty.

To clean the dust filter,

Pry off the plastic grill covering the filter with a small screwdriver.

Use a small brush, plus soap and water if necessary to clean the filter.

When the filter is dry, reposition it and snap the grill back in place.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Burleigh Wavemeter WA-1100




































































Search results

Summary of Contents for Burleigh Wavemeter WA-1100

Reviews:

Related manuals for Burleigh Wavemeter WA-1100

Brands by name

Popular brands

EXFO Burleigh Wavemeter WA-1100, Operating Manual

Search results

Summary of Contents for Burleigh Wavemeter WA-1100

Reviews:

Related manuals for Burleigh Wavemeter WA-1100

Brands by name

Popular brands