EXFO Burleigh Wavemeter WA-1100 Operating Manual Download | Manualshive

Page: 25 / 67

background image

WA-1100/WA-1600 Wavemeter Operating Manual

3 Remote Communications

3-6

08115-M-00 Rev E

SCPI Command Detail

This section provides detailed information for all instrument SCPI programming
commands. The commands are organized by subsystem.

Common Commands

*CLS

Description

The *CLS (clear status) command clears the event status register
and the error queue.

*ESE?

Description

Queries the bits in the event status enable register.

Query Response

Returns an integer which is the sum of all the bit values for those
bits that are set. (See Event Status Register Enable table below.)

*ESE <integer > mask from 0 to 255

Description

The *ESE (event status enable) command sets the bits in the event
status enable register and enables the corresponding events in the
event status register. For each bit that is set (equal to 1), it is
enabled in the event status register (ESR). <integer> is an integer
which is the sum of all of the bit values for those bits that are set.

Event Status Enable Register

Bit

Bit Value

Enables

7

128

Power On (PON)

6

64

Not Used

5

32

Command Error (CME)

4

16

Execution Error (EXE)

3

8

Device Dependent Error (DDE)

2

4

Query Error (QYE)

1

2

Not Used

0

1

Operation Complete (OPC)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
23
24
25
26
27
...
»

Summary of Contents for Burleigh Wavemeter WA-1100




































































Reviews:

No comments

Related manuals for Burleigh Wavemeter WA-1100

Brand: ABQ Industrial Pages: 15

Brand: ABQINDUSTRIAL Pages: 3

Brand: Daewoo Pages: 2

Brand: Saimo Pages: 101

Brand: Omano Pages: 14

Brand: WalkLAB Pages: 16

Professional Plus

Brand: YSI Pages: 28

Brand: Flowmetrics Pages: 102

Brand: X-Rite Pages: 21

Brand: DeNovix Pages: 93

Brand: Komshine Pages: 2

SeeSnake microReel

Brand: RIDGID Pages: 414

NEO MP18X Series

Brand: MA Pages: 3

ISOLGUARD HIG93

Brand: hakel Pages: 15

Brand: Xylem Pages: 2

Brand: X-IO Pages: 58

Brand: All-sun Pages: 11

INUKTUN MINIMAG

Brand: Eddyfi Technologies Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands