EXFO Burleigh Wavemeter WA-1100 Operating Manual Download | Manualshive

Page: 42 / 67

background image

WA-1100/WA-1600 Wavemeter Operating Manual

3 Remote Communications

08115-M-00 Rev E

3-23

TRIGger Subsystem Functions

:ABORt

Description

Halts acquisition of the current reading and returns the instrument to
an idle state.

Examples

:ABOR

:INITiate[:IMMediate]

Description

Starts the acquisition of a new reading.

Examples

:INIT
:INIT:IMM

UNIT Subsystem

For the instrument, there is a single query and command in the UNIT subsystem. They
query and change the units that the SCPI interface uses for reporting power.

UNIT Subsystem Functions

:UNIT:POWer?

Description

Queries the state of the power units that will be used when the SCPI
interface returns power values.

Query Response

{DBM | W}

Examples

:UNIT:POW?

:UNIT:POWer {DBM | W}

Description

Sets the state of the power units that will be used when the SCPI
interface returns power values. This setting does not affect the front
panel display.

*RST value

DBM

Examples

:UNIT:POW DBM
:UNIT:POW W

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
40
41
42
43
44
...
»

Summary of Contents for Burleigh Wavemeter WA-1100




































































Reviews:

No comments

Related manuals for Burleigh Wavemeter WA-1100

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: Kawai Pages: 142

Brand: Kawai Pages: 10

Brand: C-LOGIC Pages: 4

Brand: Bacharach Pages: 19

Brand: Olympus Pages: 4

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

Brand: Hilti Pages: 146

Brand: Armstrong Monitoring Corporation Pages: 12

Brand: Veeco Pages: 349

Brand: GrainPro Pages: 7

Brand: Caen Pages: 50

Brand: Lutron Electronics Pages: 23

Brand: Amrutha Technologies Pages: 22

Brand: Straightpoint Pages: 24

UNITY INOVA NMR

Brand: Varian Pages: 65

Brand: TCS Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands