manualshive.com logo in svg

Exalt EX-4.9r, Installation And Configuration Manual, Page: 13 / 115

Share
Download
Exalt EX-4.9r Installation And Configuration Manual Download Page 13

Exalt Communications Inc. 

r-series Installation and Management Manual 

5000007 (ETS) 

xiii

 

2007-02-12 (draft) 

United States Compliance..................................................................................................... 10 

EX-4.9r FCC (USA) EIRP.................................................................................................... 11 

FCC (USA) EIRP.................................................................................................................. 11 

Canada Compliance .............................................................................................................. 12 

IC (Canada) EIRP ................................................................................................................. 12 

EX-4.9r Series IC (Canada) EIRP ........................................................................................ 12 

EX-5r Series IC (Canada) EIRP ........................................................................................... 12 

ETSI Compliance – EIRP limits ........................................................................................... 13 

Time Division Duplex (TDD) Factors...................................................................................... 14 

Link Orientation and Synchronization...................................................................................... 15 

Radio A/B Configuration...................................................................................................... 15 

System Installation and Initiation Process .................................................................................... 17 

Record Keeping ........................................................................................................................ 19 

Installation..................................................................................................................................... 20 

Mechanical Configuration and Mounting................................................................................. 20 

Mounting the System ............................................................................................................ 20 

Radio Ports and Indicators ........................................................................................................ 22 

Connector Overview ............................................................................................................. 22 

LED Indicators...................................................................................................................... 23 

RESET Button ...................................................................................................................... 24 

Power ........................................................................................................................................ 24 

Terminating the RF Connectors r-(x)c Series models only)................................................. 25 

AC Power.............................................................................................................................. 25 

Power Injector....................................................................................................................... 26 

Reset to Critical Factory Settings ......................................................................................... 27 

Antenna/Transmission System.................................................................................................. 27 

Initial Antenna Mounting r-(x)c Series models only)........................................................... 29 

Transmission Line from Antenna to Radio r-(x)c Series models only ................................. 30 

RF Lightning Arrestor........................................................................................................... 32 

Antenna Alignment................................................................................................................... 32 

Configuration and Management ................................................................................................... 34 

Telnet into the Command Line Interface (CLI)........................................................................ 34 

Summary of Contents for EX-4.9r




















































































































Reviews:

No comments