PRIMACY
LAMINATION
58
APPENDIX B
COMPLIANCE STATEMENTS
In this section, you will find the certification for your Evolis printer.
FCC Federal Communications Commission notice
Radio frequency interference in the United States
The Primacy model complies with the following specification: FCC Part 15,
Subpart A, Section 15.107(a) and Section 15.109(a) Class B Digital device.
Additional information:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try the following measures:
- Reorient or relocate the receiving antenna.
- Move the equipment away from the radio or television.
- Connect the equipment to a circuit other than that to which the receiver is connected.
- Consult the supplier or an experienced radio/TV technician.
Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the FCC Rules
for Class B digital devices.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications made to this equipment without the express,
written consent of Evolis Card Printer may cause harmful interference and void the FCC authorization to operate
this equipment.
We recommend keeping a distance of 20 cm between the user and the RFID module when it is in operation.
This device is compliant with the RSS of Industry Canada applicable to radio devices exempt from licensing. Its use
is authorized under the following two conditions: (1) The device must not cause jamming and (2) the device user
must accept any radio-electrical jamming it experiences, even if this comprises its operation.
Japanese radio frequency interference (VCCI)
This equipment is Class B information technology equipment based on the rules laid down
by the Voluntary Control Council For Interference by Information Technology Equipment
(VCCI). Its use in or close to a residential area may cause radio interference, in which case
you must take appropriate steps.
Declarations of conformity
Concerning Safety and Electromagnetic Compatibility of Radio Equipment
(RED 2014/53/UE, BT 2014/35/UE, CEM 2014/30/UE Directives) and (RoHS2)
2011/65/EU)
Manufacturer name:
Evolis
Manufacturer address:
14, avenue de la Fontaine
Z.I. Angers Beaucouzé
49070 Beaucouzé, France
Equipment name:
Primacy
Year of manufacture:
June 2016
I, the undersigned,
Serge Olivier
,
Declare under my own responsibility that the product here above described
complies with the essential applicable requirements, (particularly with those
of the
RED 2014/53/UE, BT 2014/35/UE, CEM 2004/30/UE Directives and
(RoHS2) 2011/65/EU
as follows:
Article 3.1 a: (electromagnetic compatibility protection requirement)
Safety standard applied
EN60950-1: 2006 + A11 + A1 + A12 + A2
EN50364: 2010
Article 3.1 b: (electromagnetic compatibility protection requirements)
EMC standard applied
EN55032: 2012
EN55024: 2010
EN61000-3-2: 2014
EN61000-3-3: 2013
EN301489-3: 2013 (VI.6.1)
Article 3.2: (Good use of the radio frequency spectrum to avoid undesirable interferences)
EMC standard applied
EN300330-2 V1.6.1
Full name: Serge Olivier
Position: R&D Director
Date: : June 30
th
, 2016
Signature:
EUROPE -
Norway Only: This product is designed for IT power system with phase-to-
phase voltage 230 V. Earth grounding is via the polarised, 3-wire power cord.
FI: “Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”
SE: “Apparaten skall anslutas till jordat uttag”
NO: “Apparatet må tilkoples jordet stikkontakt”
DK : „Apparatets stikprop skal tilsluttes en stikkontact med jord, som giver forbindelse
til stikproppens jord“.
