EVERVIEW AR300 series User Manual Download

Page: 66 / 179

User Manual of Digital Video Recorder

Note:

The record files of which the recording is still not completed can’t be locked.

Click

to change it as

to unlock the file and the file is not protected.

Figure 5.37 Unlocking Attention

Protect file by setting HDD property to Read-only

Note:

To edit HDD property, you need to set the storage mode of the HDD to Group. See

Chapter 10.3

Managing HDD Group.

Steps:

Enter HDD setting interface.

Menu> HDD

Figure 5.38 HDD General

Click

to edit the HDD you want to protect.

Figure 5.39 HDD General- Editing

Set the HDD to Read-only.

Click

to save settings and back to the upper level menu.

Note:

You can’t save any files in a Read-only HDD. If you want to save files in the HDD, change the

property to R/W.

Summary of Contents for AR300 series




















































































































































































Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands

EVERVIEW AR300 series, User Manual

Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands