EVERVIEW AR300 series User Manual Download

Page: 21 / 179

User Manual of Digital Video Recorder

1.6 Starting Up and Shutting Down the Device

Purpose:

Proper startup and shutdown procedures are crucial to expanding the life of the device.

Before you start:

Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground

connection is working properly.

Starting up the device:

Steps:

Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device.

Press the

POWER

button on the rear panel. The Power indicator LED should turn green indicating that

the unit begins to start up.

Shutting down the device:

Steps:

Enter the Shutdown menu.

Menu > Shutdown

Figure 1.9 Shutdown Menu

Click the

Shutdown

button to enter the following dialog box:

Figure 1.10 Dialog Box for Shutdown

Click the

Yes

button. The following message box pops up:

Figure 1.11 Message Box for Power Off

Turn off the power switch on the rear panel of DVR.

Rebooting the device

In the Shutdown menu (Figure 1.9), you can also click

Reboot

to reboot the device.

Summary of Contents for AR300 series




















































































































































































Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands

EVERVIEW AR300 series, User Manual

Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands