EVERVIEW AR300 series User Manual Download Page 114

Page: 114 / 179

User Manual of Digital Video Recorder

113

8.5 Handling Exceptions

Purpose:

Exception settings refer to the handling method of various exceptions, e.g.,

• HDD Full:

The HDD is full.

• HDD Error:

Writing HDD error, unformatted HDD, etc.

• Network Disconnected:

Disconnected network cable.

• IP Conflicted:

Duplicated IP address.

• Illegal Login:

Incorrect user ID or password.

• Input / Output Video Standard Mismatch:

I/O video standards do not match.

• Record Exception:

No space for saving recorded file.

Steps:

Enter

Exceptions

interface of System Configuration and handle various exceptions.

Menu> Configuration> Exceptions

Please refer to

Chapter 8.6

for detailed alarm response actions.

Figure 8.16 Exceptions Setup Interface

Summary of Contents for AR300 series




















































































































































































Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands

EVERVIEW AR300 series, User Manual

Search results

Summary of Contents for AR300 series

Reviews:

Related manuals for AR300 series

Brands by name

Popular brands