evertz 7700 Series Manual Download Page 37

Page: 37 / 94

7700 MultiFrame Manual

7736CEM Composite Encoder with Monitoring

Revision 1.5

Page - 27

*Grey background indicates un-implemented or un-tested features

7.5.22. Setting the Message to be Displayed When There Is No Incoming SID

Video/SID

This control sets the message that will be displayed in the SID window when
there is no incoming source ID on the VITC. The text of the message can be
changed. See section 7.2 for information on changing text fields.

Default SID
msg

No SID

7.6.

CONFIGURING THE VIDEO PROCESSING CONTROLS

The

Video Processing

menu is used to configure parameters associated with the composite encoder

video processing. The chart below shows the items available in the

Video Processing

menu.

VBI Proc

Selecting this item takes you into the VBI Processing Menu

NTSC setup
pedestal

Selects whether the NTSC 7.5 IRE pedestal will be added to the composite
analog output video

Line 21 setup

Controls line 21 processing

Colour Bars

Turn on internally generated colour bar test signal

Composite display
mode

Selection of colour or B/W modes

Video level

Controls the output video level

Hue

Controls the output video hue

Saturation

Controls the output video saturation

Contrast

Controls the output video white level

Brightness

Controls the output video black level

H blanking

Controls the width of horizontal blanking

VBI processing

Either pass or blank the vertical blanking interval lines

Y Filter Selection

Standard composite filtering or adjustable filtering is selectable

Wideband Y Freq.
Resp.

Controls the frequency response with the wideband filter selected

Chroma Filter
Selection

Various chroma bandwidths are available with this control

Summary of Contents for 7700 Series































































































Search results

Summary of Contents for 7700 Series

Reviews:

Related manuals for 7700 Series

Brands by name

Popular brands

evertz 7700 Series, Manual

Search results

Summary of Contents for 7700 Series

Reviews:

Related manuals for 7700 Series

Brands by name

Popular brands