evertz 7700 Series Manual Download Page 20 | Manualshive

Page: 20 / 94

background image

7700 MultiFrame Manual
7736CEM Composite Encoder with Monitoring

Page - 10

Revision 1.5

*Grey background indicates un-implemented or un-tested features

4.2.

AUDIO STATUS LEDS

Four LEDs located on the lower end of the module (near the card extractor) indicate which audio channels
are present. Audio channel 1 LED is located closest to the center of the module. Digital audio presence is
determined by the AES receiver lock indicator (when AES input is selected). When embedded audio is
selected, the channel must be present on the selected group for the LED to illuminate.

Audio
LED

Colour

Audio Channel Status

1

Off

No channel 1 present.

Green

Channel 1 present.

2

Off

No channel 2 present.

Green

Channel 2 present.

3

Off

No channel 3 present.

Green

Channel 3 present.

4

Off

No channel 4 present.

Green

Channel 4 present.

Table 4-1: Audio Channel Status LEDs

«
...
18
19
20
21
22
...
»

Summary of Contents for 7700 Series































































































Reviews:

No comments

Related manuals for 7700 Series

Brand: Yuasa Pages: 12

VIV Six Five Series

Brand: Memphis Pages: 16

Brand: K+H Pages: 96

Brand: Sure Electronics Pages: 16

Brand: Stageline Pages: 18

Brand: AAS Pages: 8

99 Stereo Power Amplifier

Brand: QUAD Pages: 18

Brand: Cyrus Pages: 25

Brand: Altinex Pages: 9

Brand: NXP Semiconductors Pages: 9

Brand: Mark Levinson Pages: 38

427 SMALL BLOCK

Brand: Ashdown Pages: 12

Brand: NAD Pages: 37

Brand: Dared Pages: 6

Brand: JET CITY AMPLIFICATION Pages: 18

Brand: soundsation Pages: 10

4-151-113-11 (1)

Brand: Sony Pages: 2

Brand: Mi-Light Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands