evertz 7700 Series Manual Download Page 36 | Manualshive

Page: 36 / 94

background image

7700 MultiFrame Manual
7736CEM Composite Encoder with Monitoring

Page - 26

Revision 1.5

*Grey background indicates un-implemented or un-tested features

7.5.17. Setting the VITC Line Number – 525 Line Video

Video/SID

With this control, set the VBI line number that contains the VITC information
when operating in NTSC video mode.

If the VITC contains Source ID (SID) information, the card will automatically
decode it, and turn on the SID window if the user has enabled this window.

If the wrong line number is set, no time code (or SID) will be decoded.

525 VITC line

10 to 32
10

7.5.18. Setting the VITC Line Number – 625 Line Video

Video/SID

With this control, set the VBI line number that contains the VITC information
when operating in PAL-B video mode.

If the VITC contains Source ID (SID) information, the card will automatically
decode it, and turn on the SID window if the user has enabled this feature.

If the wrong line number is set, no time code (or SID) will be decoded.

625 VITC line

6 to 32
10

7.5.19. Setting the PESA Source ID Line Number – 525 Line Video

Video/SID

With this control, set the VBI line number that contains the PESA SID
information when operating in NTSC video mode. If the wrong line number is
set, no SID will be decoded.

525 PESA line

10 to 21
11

7.5.20. Setting the PESA Source ID Line Number – 625 Line Video

Video/SID

With this control, set the VBI line number that contains the PESA SID
information when operating in PAL-B video mode. If the wrong line number is
set, no SID will be decoded.

625 PESA line

7 to 22
11

7.5.21. Setting the Default SID Mode

Video/SID

Determines if the Default SID message will be displayed in the SID window
when there is no incoming source ID on the VITC.

Set to

Disable

to blank the SID window when there is no incoming source ID.

Set to

Enable

to show the Default SID message in the SID window when there

is no incoming source ID. The SID window must also be turned On

to display

the default SID message. See section 7.9.3 for information on turning the SID
window On.

Default SID
mode

Disable
Enable

«
...
34
35
36
37
38
...
»

Summary of Contents for 7700 Series































































































Reviews:

No comments

Related manuals for 7700 Series

Brand: Parasound Pages: 16

Brand: Nakamichi Pages: 34

Brand: Hill Audio Pages: 12

PHANTOM CI AMP-2500 DSP

Brand: Dali Pages: 29

Brand: DigiTech Pages: 4

Brand: Unika Pages: 16

Brand: Bugera Pages: 15

Okur A7 Series A71100.1

Brand: DB Drive Pages: 12

Brand: Texas Instruments Pages: 26

Brand: Custom Valve 50 Pages: 14

Brand: Crate Pages: 4

Brand: Pyramid Pages: 16

Brand: Parasound Pages: 10

Brand: Rane Pages: 16

Brand: ELECTROCOMPANIET Pages: 16

Brand: A SYSTEMS Pages: 16

EVOLUTION THREE 3A6

Brand: crescendo Pages: 32

Brand: zapco Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands