Everlast PowerPlasma 60S, Operator'S Manual

Page: 10 / 26

10
Specification PowerPlasma 60S PowerPlasma 70S PowerPlasma 80S
Inverter Type Analog, Siemens IGBT
Module Construction Analog, Siemens IGBT
Module Construction Analog, Siemens IGBT
Module Construction
Minimum/Maximum Rated Output 20 A/88 V - 60 A/108 V 20 A/88 V-70 A/110V 20 A/88 V-80 A/112 V
Start Type Blow-Back Type Blow-Back Type Blow-Back Type
Torch Type Trafimet S-75 12 ft. Trafimet S-75 12 ft. Trafimet S-75 12 ft.
Duty Cycle @ Rated Amps/Volts ( 40° C)
(Output V/A) 60% @ 60 A/ 108 V
100% @ 46.5 A/ 98.6 V 60% @ 70 A/ 110 V
100% @ 55 A/102 V 60% @ 80 A/112 V
100% @ 63 A/105 V
OCV (U0) 200 V 200 V 200 V
Voltage Input (U1) Standard 220/ 240 V;
50/60Hz 1 Phase Standard 220/ 240 V;
50/60Hz 1 Phase Standard 220/ 240 V;
50/60Hz 1 Phase
(3 phase Optional)
Maximum Inrush Amps
(I1MAX) 50 A @ 220 V; 46 A @ 240 V 60 @ 220 V; 55 A@ 240 V 70 @220 V; 64 @ 240 V
Maximum Rated Effective Amps (I1EFF) 40 A @ 220 V; 36 A @ 240 V 47 A @ 220 V; 44 @ 240 V 55 A @ 220 V; 51 A @ 240 V
CNC Port Yes Yes Yes
Air Post Flow Timer Adjustable Adjustable Adjustable
Minimum Air CompressorRequirement 5 CFM @ 90 psi/
30-60 gallon reserve 6 CFM @ 90 psi/
30-60 gallon reserve 7 CFM @ 90 psi/
30-60 gallon reserve
Duty Cycle/ Over Current Protection Yes Yes Yes
Minimum Operating Air Pressure
(Safety Cut-Out Threshold) 35 psi 35 psi 35 psi
Recommended Operating Air Pressure
(Set with Air Flow set “Test”) 70-75 psi
70-75 psi
70-75 psi
Maximum Permissible Static Air Pressure
(Without air flowing) 85 psi 85 psi 85 psi
Maximum Supplied Air Pressure
(From Compressor/Tank) 90 psi 90 psi 90 psi
Recommended Daily Maximum
Average Cut Thickness (Hand Torch) 5/8” 3/4” 1”
Recommended Daily Maximum
Average Cut Thickness (CNC) 3/8” 1/2” 5/8”
Rated Maximum Quality Cut @
10-12 IPM (Steel) 7/8” 1 1/8” 1 1/4”
Max Severance Cut @ 3 IPM (Steel ) 1 1/4” 1 3/8” 1 1/2”
Minimum Water Ingress Protection Standard IP21S IP21S IP21S
Efficiency >85% >85% >85%
Cooling Method Full Time High Velocity Fan
with Tunnel design Full Time High Velocity Fan
with Tunnel design Full Time High Velocity Fan
with Tunnel design
Dimensions (approximate) 18” H X 10” W X 25” L 18” H X 10” W X 25” L 18” H X 10” W X 25” L
Weight (Bare Unit) 65 lbs 68 lbs 70 lbs
Introduction and Specifications Section 1
Decrease maximum cut thickness values for aluminum and stainless by approximately 35%.