EverFocus ECOR 4D Instruction Manual Download

Page: 70 / 107

6 Networking Overview

This chapter will give you a basic instruction on how to set up the DVR for network connection. It is highly

recommended that you have a working knowledge of what a network is and how it works. This will be

helpful in completing the networking process.

6.1 Introduction to TCP/IP

TCP/IP is the group of protocols used by the Internet and most Local Area Networks (LANs) throughout the

world. In TCP/IP, every computer or other communications device that is connected to the network has a

unique IP address. By doing this you are giving your device a unique address similar to the address of your

house. An IP address is composed of four octets (numbers in the range of 0 to 255) separated by decimal

points. The IP address is used to uniquely identify a host or computer on the LAN. For example, one

computer on a network could have an IP address of 192.168.1.127.

You should never give two or more devices the same exact IP address, but the first three octets of an IP

address should be the same for all computers in the local area network. For example, if a total of 253

computers exist in a single LAN, the IP addresses could be assigned starting with 192.168.1.

, where

represents a number in the range of 2 to 254.

6.2 Subnet Masks

Each host in a LAN has a subnet mask. The

subnet mask

is a set of octets that is used to determine which

LAN or class it belongs to. The number 255 is usually used to represent the network address portion of the

IP address and a zero is placed at the end to identify the host portion of the address. Basically the subnet

mask can be compared to the city you live in for your home address, but in this case you are stating the

network you belong too.

6.3 Gateway Address

Each host in a LAN has a gateway. A

gateway address

is composed of four octets separated by decimal

points. The gateway address is used to uniquely identify the main host or computer on the LAN that

assigns the IP addresses to your network (usually a router). This is comparable to the zip code of your

address.

Chapter

Summary of Contents for ECOR 4D












































































































Search results

Summary of Contents for ECOR 4D

Reviews:

Related manuals for ECOR 4D

Brands by name

Popular brands

EverFocus ECOR 4D, Instruction Manual

Search results

Summary of Contents for ECOR 4D

Reviews:

Related manuals for ECOR 4D

Brands by name

Popular brands