background image

4

Although the battery is designed for professional protection, it can still become 
damaged. If the battery case is seriously damaged and cracked, a small amount of 
battery liquid will overflow from the battery. If there is a fire nearby and the battery 
fails to be handled in time, an explosion could be caused, and the battery will produce 
thick smoke, CO, CO2 and other gases. 

In case of emergency, following measures shall be taken:

1

  If battery fluid is accidentally splashed into eyes, immediately clean it with plenty  

 

of clean water and seek medical treatment. 

2

  If the battery liquid accidentally contacts the skin, scrub and clean it  

 

 

with soap immediately. 

3

  If you inhale gas and feel unwell, dizzy or start vomiting, seek a Doctor 

 

 

straight away. 

4

  If there’s fire in the location where the battery is installed, heptafluoropropane 

 

 

(FM-200) or carbon dioxide (CO2) fire extinguishers should be used to put out 

 

 

the fire. 

5

  Use an ABC fire extinguisher, if the fire is not caused by battery and has not  

 

spread to it yet.

1.3 Emergency Measures

 Warning

•  If conflagration has just occurred and not spread yet, ensuring the safety  
 

of yourself, try to disconnect the circuit breaker of the battery and cut off  

 

the main power.

•  If the battery is on fire, do not try to extinguish the fire, 

 

 

evacuate immediately.

Summary of Contents for B1-5.1-48

























Reviews: