EverAccess EFC-02-1A User Manual Download

Page: 62 / 75

enter-door reader or exit-door reader. The default setting for Alarm Action Setting

and Extended Alarm Setting is: no alarm output is generated per card anti-passback

fail event, as shown in the following two figures, respectively. Change settings

according to sections “Enter Alarm Action Setting Sub-menu” and “Enter Extended

Alarm Setting Sub-menu”.

Card PIN Fail

For password setting, please refer to section “Set Card PIN Setting” in this chapter. A

Card PIN Fail event will be generated when the card is swiped at the reader and PIN

is required to gain access but the cardholder enters wrong PIN three times

consecutively. The default setting for Alarm Action Setting and Extended Alarm

Setting is: no alarm output is generated per card PIN fail event, as shown in the

following two figures, respectively. Change settings according to sections “Enter

Alarm Action Setting Sub-menu” and “Enter Extended Alarm Setting Sub-menu”.

Door Forced Open

A Door Forced Open event will be generated when controller detects that a door is

opened from the door sensor without any legitimate swipe card or door open button

push operation taking place. The default setting for Alarm Action Setting and

Extended Alarm Setting is: no alarm output is generated per door forced open event,

as shown in the following two figures, respectively. Change settings according to

sections “Enter Alarm Action Setting Sub-menu” and “Enter Extended Alarm

Setting Sub-menu”.

Door Held Open

A Door Held Open event will be generated when a door is opened by legitimate

swipe card or door open button push operation but is still not closed after the “over

time” in door setting has elapsed. The default setting for Alarm Action Setting and

Extended Alarm Setting is: no alarm output is generated per door held open event, as

shown in the following two figures, respectively. Change settings according to

sections “Enter Alarm Action Setting Sub-menu” and “Enter Extended Alarm

Setting Sub-menu”.

Door Held Open
NNNNNNNN-NN

Door Held Open
NNNNNNNN

Door Forced Open
NNNNNNNN

Door Forced Open
NNNNNNNN-NN

Card PIN Fail
NNNNNNNN

Card APB Fail
NNNNNNNN-NN

Card APB Fail
NNNNNNNN

Card PIN Fail
NNNNNNNN-NN

Summary of Contents for EFC-02-1A












































































Search results

Summary of Contents for EFC-02-1A

Reviews:

Related manuals for EFC-02-1A

Brands by name

Popular brands

EverAccess EFC-02-1A, User Manual

Search results

Summary of Contents for EFC-02-1A

Reviews:

Related manuals for EFC-02-1A

Brands by name

Popular brands