EverAccess EFC-02-1A User Manual Download

Page: 60 / 75

Alarm IN 0

Alarm In 0 event will be generated when Alarm In 0 input is active. The default

setting for Alarm Action Setting and Extended Alarm Setting is: only Main alarm

output on main module has alarm output per Alarm In 0 event, as shown in the

following two figures, respectively. Change settings according to sections “Enter

Alarm Action Setting Sub-menu” and “Enter Extended Alarm Setting Sub-menu”.

Remote Alarm

System administrator can directly generate alarm signal using control software when

he observes abnormal condition through surveillance system such as CCTV. This is

defined as a Remote Alarm event. The default setting for Alarm Action Setting and

Extended Alarm Setting is: only Main alarm output on main module has alarm output

per remote alarm event, as shown in the following two figures, respectively. Change

settings according to sections “Enter Alarm Action Setting Sub-menu” and “Enter

Extended Alarm Setting Sub-menu”.

Unknown Card

Unknown card refers to a card that is never logged in the system. An Unknown Card

event will be generated when an unknown card is swiped on the reader. The default

setting for Alarm Action Setting and Extended Alarm Setting is: no alarm output is

generated per unknown card event, as shown in the following two figures,

respectively. Change settings according to sections “Enter Alarm Action Setting Sub-

menu” and “Enter Extended Alarm Setting Sub-menu”.

Expired Card

Any card in the system is usually assigned a valid date. After the valid date is passed

the controller will automatically set the card as an expired card. An expired card

cannot gain access to the system. At the same time, an Expired Card event will be

generated when an expired card is swiped on the reader. The default setting for Alarm

Action Setting and Extended Alarm Setting is: no alarm output is generated per

expired card event, as shown in the following two figures, respectively. Change

settings according to sections “Enter Alarm Action Setting Sub-menu” and “Enter

Extended Alarm Setting Sub-menu”.

Unknown Card
NNNNNNNN

Unknown Card
NNNNNNNN-NN

Remote Alarm
NNNNNNNN

Alarm In 0
NNNNNNNN-YN

Alarm In 0
NNNNNNNN

Remote Alarm
NNNNNNNN-YN

Summary of Contents for EFC-02-1A












































































Search results

Summary of Contents for EFC-02-1A

Reviews:

Related manuals for EFC-02-1A

Brands by name

Popular brands

EverAccess EFC-02-1A, User Manual

Search results

Summary of Contents for EFC-02-1A

Reviews:

Related manuals for EFC-02-1A

Brands by name

Popular brands