background image

EVER UPS SINLINE RT / RT XL series instruction manual

 

2017-04-26 12:41 

Pomoc Techniczna, tel.: +48 61 6500 400 

www.ever.eu 

 

SAFETY INSTRUCTIONS AND RECOMMENDATIONS 

A)  General remarks 

 

CAUTION!

  Before  starting  the  procedures  described  in  this  manual, 

please  read  the  general  safety  instructions  (including  the  instructions 

found  in  this  document),  health  &  safety  information,  environmental 

protection  information  and  legal  regulations  that  may  apply.  Always 

observe the instructions and recommendations in these documents.  

 

 

CAUTION! 

The user is strictly forbidden from performing any repairs, as 

this  would  constitute  a  health  hazard  and  may  result  in  death.  Any 

repairs  and  replacement  of  batteries  should  be  carried  out  only  by 

suitably qualified service technicians with professional  licenses required 

by law.

 

 

 

 

CAUTION!

  The  unit  should  be  operated  and  stored  in  conditions 

complying  with  the  requirements  set  in  the  specification  (technical 

documentation). 

 

 

CAUTION! 

The  device  is  completely  disconnected  from  the  mains  only 

when  the  power  lead  is  removed  from  the  mains  socket  (the  plug  is 

removed from the mains socket).

 

 

 

CAUTION!

 The unit is equipped with an internal power source (batteries) 

or  it  may  operate  in  combination  with  a  fixed,  external  source  of  power 

(battery  packs).  Dangerous  voltage  may  be  present  at  the  output 

terminal(s), even if the unit has been disconnected from the mains. 

 

 

CAUTION! 

The  user  should  place  warning  labels  on  all  remotely 

installed  primary  isolation  switches  in  order  to  warn  electrical  service 

technicians  that  the  circuit  is  powered  by  a  UPS  unit.  The  following  (or 

equivalent) text should be used on such warning labels: 

DISCONNECT  THE  UPS  SYSTEM  BEFORE  STARTING  WORK  ON  THIS 

CIRCUIT. 

 

Summary of Contents for SINLINE RT












































































Reviews: