Evco Vcolor 818 Installer Manual Download Page 7

Page: 7 / 94

EVCO S.p.A.

Vcolor 818

| Installer manual ver. 1.1 | Code 144VC818E114

page 7 of 94

Analogue outputs (PWM)

Vcolor 818

evaporator fan

(1)

Digital outputs (electromechanical relays; A res. @

250 VAC)

Vcolor 818

compressor

16 A

defrosting

8 A

evaporator fan

8 A

condenser fan

8 A

door heating elements

8 A

needle probe heating

16 A

load 7 (default room light) (1)

8 A

load 8 (default pump down valve) (2)

8 A

Communication port

Vcolor 818

RS-485 serial port with MODBUS communication protocol

•

USB serial port

•

Other features

Vcolor 818

protection rating of the user interface

IP65

clock

•

alarm buzzer

•

hard / soft function

•

“programs” function

•

“HACCP” function

•

Notes:

(1)

Configurable for dehumidifier or condenser fan.

(2)

Configurable for pump down valve or evaporator fan.

For further information, see chapter "TECHNICAL DATA"; for other models contact the EVCO sales network.

Summary of Contents for Vcolor 818































































































Search results

Summary of Contents for Vcolor 818

Reviews:

Related manuals for Vcolor 818

Brands by name

Popular brands

Evco Vcolor 818, Installer Manual

Search results

Summary of Contents for Vcolor 818

Reviews:

Related manuals for Vcolor 818

Brands by name

Popular brands