EUTECH INSTRUMENTS alpha TDS 200 Instruction Manual Download

Page: 7 / 40

OVERVIEW

3.1

Front Panel

The front panel consists of a 4-digit LED display, 8 LED annunciators and 4 keys.

Annunciators

1. REL 1

Displayed when Relay 1 is activated

2. REL 2

Displayed when Relay 2 is activated

3. MEAS

Displayed in measurement mode

4. CAL

Displayed in calibration mode

5. SETUP

Displayed in setup mode

6. ppm

Displayed when measurement range in parts-per-million

Unit of the displayed parameter (temperature)

8. ppt

Displayed when measurement range in parts-per-thousands

Keys

9. MODE

Toggle between TDS and temperature display

10. ENTER

Confirm changes or to enter into further levels of sub-menu

11.

▲

(

increment)

Use during calibration and setup modes to increment values.
Press

▲

▼

keys together to escape to Measurement mode

11.

▼

(decrement)

Use during calibration and setup modes to decrease values.
Press

▲

▼

keys together to escape to Measurement mode

12. LED Display

14 segment LED display

8.8.8.8.

Summary of Contents for alpha TDS 200









































Search results

Summary of Contents for alpha TDS 200

Reviews:

Related manuals for alpha TDS 200

Brands by name

Popular brands

EUTECH INSTRUMENTS alpha TDS 200, Instruction Manual

Search results

Summary of Contents for alpha TDS 200

Reviews:

Related manuals for alpha TDS 200

Brands by name

Popular brands