manualshive.com logo in svg

Eurotech Apollo, User Manual

Share
Download
Eurotech Apollo User Manual Download Page 8

APOLLO user manual 

 

Issue G

 

8 

Features 

Processor 

•

 

Intel Pentium M and Celeron M processor options.  

Chipset 

•

 

North Bridge: Intel 82555GME.  

•

 

South Bridge: Intel 82801DB/ICH4.  

•

 

400MHz processor side bus speed. 

System memory 

•

 

Up to 1024MB PC2700 DDR DIMM. 

BIOS 

•

 

PhoenixBIOS boot from HDD, FDD, CDROM, CompactFlash

®

, USB device or 

network boot. 

Video 

•

 

Integrated Intel Extreme Graphics 2. 

•

 

VGA CRT interface - 2048 x 1536 at 75Hz.  

•

 

LVDS interface (single/dual channel) -1600 x 1200 at 60Hz.  

•

 

Dual graphics controller - allows for two independent video displays. 

•

 

Additional DVI and CRT add-on modules are also available. 

Audio 

•

 

AC97 codec with support for six channel 5.1 speaker output.  

•

 

S/PDIF (Sony/Philips Digital Interface) compressed digital output to optical 
transmitter.  

Network support 

•

 

Dual 10/100baseTx Ethernet ports or a build variant for 10/100 and 10/100/1000 
Ethernet ports. 

USB interface 

•

 

Six USB 2.0 channels: four on-board; two via an add-on module.  

Serial ports 

•

 

Two RS232.  

•

 

One RS232/IrDA. 

•

 

One RS232/422/485. 

Summary of Contents for Apollo


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands