manualshive.com logo in svg

Eurotech Apollo, User Manual

Share
Download
Eurotech Apollo User Manual Download Page 110

APOLLO user manual 

 

Issue G

 

110 

IrDA/ASK-IR 

An infrared port is available which supports the following infrared standards: 

•

 

Infrared Data Association (IrDA) V1.0 SIR with baud rates to 115.2k/bps. 

•

 

SHARP ASK-IR protocol with maximum baud rate up to 57.6k/bps. 

For connector details, see page 

36

. 

 

Enabling the infrared port prevents operation of Serial Port B (COM2). The 
infrared port should be disconnected before using the COM2 port. 

The following diagram shows the connection of the IrDA interface port J26 to a Sharp 
GP2W0004YP IrDA transceiver module for IrDA 1.0 compliant data transmission.  

Parallel port 

The APOLLO provides a parallel port that can be used to connect an external printer, 
tape drive, disk drive, scanner etc., or can provide additional digital I/O capability. 

The port is both IBM XT/AT and IEEE1284 compatible. It supports Standard Parallel Port 
(SPP), Enhanced Parallel Port (EPP) and Extended Capabilities Port (ECP) modes and 
is compliant with the IEEE1284 specification. It also incorporates ChiProtect circuitry, 
which prevents possible damage to the parallel port due to printer power-up. 

For connector details, see page 

37

. Configuration of the parallel port operating mode is 

performed in the 

I/O Device Configuration

 menu in the BIOS; see page 

62

 for details. 

6      5      4       3       2      1

2R7

+5V

GND

RXD

TXD

22uF

100nF

+

Summary of Contents for Apollo


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands