manualshive.com logo in svg

Eurotech Apollo, User Manual

Share
Download
Eurotech Apollo User Manual Download Page 66

APOLLO user manual 

 

Issue G

 

66 

Configuring parallel ports 

To specify parallel port configuration settings, highlight 

Parallel Port Configuration 

in 

the 

I/O Device Configuration 

menu and press 

Enter

. The following screen is displayed: 

 

The details you are prompted to specify are explained in the following table: 

Field 

Explanation 

Parallel port 

Choose how this port is to be configured. The options available 
are: 

•

 

Disabled

. The port is not configured at all - it is turned off. 

•

 

Enabled

. You are going to configure the port (by completing 

the following fields). 

•

 

Auto

. The port is configured automatically by the BIOS or the 

operating system. 

OS Controlled

 is displayed if configuration of the port is 

controlled by the operating system. 

Mode 

Set the mode for the parallel port. The options you can choose 
are listed in the 

Item Specific Help

 panel on the right. 

Base I/O Address 

Specify the I/O address to be used by the parallel port. This can 
be 378 or 278. 

Interrupt 

Specify the interrupt line to be used by the parallel port. This can 
be IRQ5 or IRQ7. 

DMA channel 

Set up the DMA channel for the parallel port. You can choose 

DMA 1 

or 

DMA 3

. 

Summary of Contents for Apollo


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands