manualshive.com logo in svg

Eurotech Apollo, User Manual

Share
Download
Eurotech Apollo User Manual Download Page 56

APOLLO user manual 

 

Issue G

 

56 

The details you are prompted to specify for the drive are explained in the following table: 

Field 

Explanation 

Type 

Specify the type of drive installed as the selected master or slave 
drive. 

 

Use the 

+

 and 

-

 keys to choose a drive type. 

You can choose: 

•

 

User

. Enables you to enter details of the drive’s cylinders, 

heads and sectors yourself. 

•

 

Auto

. Details of the device are completed for you 

automatically. This is offered by default when a drive is 
attached. 

•

 

None

. Displayed automatically if no device is attached. 

•

 

ATAPI Removable

. To indicate a removable ATAPI drive.  

•

 

CD-ROM

. To indicate a CD-ROM drive. 

•

 

IDE Removable

. To indicate a removable IDE drive. 

•

 

Other ATAPI

. To indicate any other ATAPI drive. 

CHS format 

If you chose 

User

 in the 

Type

 field, specify information about the 

drive in Cylinder/Head/Sector format, as follows: 

•

 

Cylinders

. The number of cylinders. This can be between 1 

and 65,535. 

•

 

Heads

. The number of read/write heads. This must be 

between 1 and 16. 

•

 

Sectors

. The number of sectors per track. This must be 

between 1 and 63. 

Maximum Capacity

 shows the amount of space on the drive, in 

MB. 

 

Use the 

+

 and 

-

 keys to choose the numbers you require. 

 

Drives greater than 8GB operate in LBA format only. 

 

LBA Format 

If you chose 

User

 in the 

Type

 field, information is shown about 

the drive in Logical Block Address format: 

•

 

Total Sectors

. The total number of sectors on the drive. 

•

 

Maximum Capacity

. The maximum capacity of this drive as 

part of this system. 

Summary of Contents for Apollo


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands