Euromate VisionAir, User Manual

Page: 18 / 40

18
8.2.1.1 Setting the minimum fan speed
See 8.2 for the steps to call up the menu.
The gas sensor can be selected by pressing the ENTER
button [D]. Pressing the ENTER button [D] allows the
minimum speed to be set from 0-6 (but never higher
that the set maximum speed, see 8.2) with the
pq
buttons [F] [G].
To confirm the selection, press the PROGRAM button
[H].
8.2.1.2 Setting the maximum fan speed
See 8.2 for the steps to call up the menu.
The maximum speed can be selected by pressing the
button [G]. Pressing the ENTER button [D] allows the
maximum speed to be set from 0-6 (but never higher
that the set maximum speed, see 8.2) with the
pq
buttons [F] [G]. To confirm the selection, press the
PROGRAM button [H].
8.2.1.3 Setting the sensitivity
See 8.2 for the steps to call up the menu.
The sensitivity can be selected by pressing the
pq
buttons [F] [G]. The sensitivity can be set from 1-4 by
pressing the ENTER [D] button. To confirm the
selection, press the PROGRAM button [H]. This value
is dependent on the impurities in the immediate
vicinity of the air cleaner.
8.2.2 Setting of the dust sensor (only visible if installed)
The dust sensor is switched on with the AUTO button [E].
During the heating up of the sensor (approx. five minutes), the
text ‘sens cal’ appears on the display of the air cleaner. The system
then switches to the analysis phase.
The air quality is analysed for a period of two minutes at the
lowest fan speed. The correct fan speed is then set automatically.
During a change of fan speed, this new speed is shown on the
display. The minimum time that the fan runs at this speed has to
be adjusted. See 8.2.12. If no impurities are measured for 15
minutes, the fan will start again for two minutes to create an air
circulation in the room.
The dust sensor is switched off again by pressing the OFF button
or one of the buttons to increase or decrease the fan speed.
Various parameters can be set to adapt the function to the
specific situation. These parameters of the dust sensor are set by
your dealer. If the air cleaner does not react according to your
requirements, please contact your dealer. These settings are:
- Minimum fan speed
(irrespective of the gas sensor value).
- Maximum fan speed
(irrespective of the gas sensor value).
- Mode of the dust sensor.
The sensor reacts to “large – small – both” particles.
8.2.2.1 Setting the minimum fan speed
See 8.2 for the steps to call up the menu.
The DustMonitor (dust sensor) can be selected by
pressing the
pq
buttons [F] [G].
Pressing the ENTER button [D] allows the minimum
speed to be set from 0-6 (but never higher that the set
maximum speed, see 8.2) with the
pq
buttons [F] [G].
To confirm the selection, press the PROGRAM button
[H].
8.2.2.1 Setting the maximum fan speed
See 8.2 for the steps to call up the menu.
The maximum speed can be selected by pressing the
pq
buttons [F] [G]. Pressing the ENTER button [D]
allows the maximum speed to be set from 0-6 (but
never higher that the set maximum speed, see 8.2)
with the
pq
buttons [F] [G]. To confirm the selection,
press the PROGRAM button [H].
8.2.2.3 Setting the mode
See 8.2 for the steps to call up the menu.
The mode can be selected by pressing the
pq
buttons
[F] [G]. Press the ENTER button [D] allows the mode to
be selected so that the dust sensor reacts to large
particles (PM10), small particles (PM2,5) or both with
the
pq
buttons [F] [G] . To confirm the selection, press
the PROGRAM button [H]. This value is dependent on
the impurities in the immediate vicinity of the air
cleaner.
These particle sizes are derived and are not actually
measured.
8.2.2 Setting the X-Changer
The X-Changer is an hourmeter that counts down from a value set
by the dealer. The degree of contamination is also taken into
consideration. When the set value has counted down to zero, the
filter change symbol (see 8.3) will be displayed.
The X-Changer can be switched on or off according to the user’s
wishes. The sensitivity can also be set. The installer estimates the
contamination and then sets the hourmeter accordingly. The
hourmeter can also be reset. If the air cleaner does not react
according to your requirements, please contact your dealer. These
settings are:
DUST SENSOR