background image

16 

 

TROUBLESHOOTING 

Fault 

Possible Cause 

Solution 

Light on, but motor 

does not work 

Fan switch turned off

 

Select a fan switch position. 

Fan switch failed

 

Contact 

service centre. 

Motor failed 

Contact service 

centre. 

Light does not 

work, motor does 

not work 

House fuses blown 

Reset/Replace fuses. 

Power cord loose or 

disconnected 

Refit cord to power outlet. 

Switch power outlet on. 

Lights not working 

Insufficient suction 

Broken/Faulty globes

 

Replace globes as per this 

instruction. 

The distance between the 

Rangehood and the gas top is 

too far 

Refit the Rangehood to the 

correct distance. 

The Rangehood 

inclines 

The fixing screw not tight 

enough 

Tighten the hanging screw and 

make it horizontal. 

 

 

NOTE:  

Any electrical repairs to this appliance must conform to your local, state and 

federal 

laws. Please

 contact the service centre if in any doubt before 

undertaking any of the 

above. Always 

disconnect the unit from the power 

source when opening the unit. 

 

 

MAINTENANCE AND CLEANING

 

Caution:

 

• Before maintenance or cleaning is carried out, the 

Rangehood should be disconnected from the main power 

supply. Ensure that the Rangehood is switched off at the wall 

socket and the plug removed. 

 

• External surfaces are susceptible to scratches and abrasions, 

so please follow the cleaning instructions to ensure the best 

possible result is achieved without damage. 

 

GENERAL 

Cleaning and maintenance should be

 carried out with the appliance cold especially 

when 

cleaning. Avoid

 leaving alkaline or acid substances (lemon juice, vinegar etc.) on 

the surfaces. 

 

STAINLESS STEEL 

The stainless steel must be cleaned regularly (e.g. Weekly) to ensure long life 

expectancy. Dry 

with a clean soft cloth. A 

specialized stainless-steel cleaning fluid may 

be used.

 

NOTE: 

 

Ensure that wiping is done along with the grain of the stainless steel to prevent any 

unsightly crisscross scratching patterns from appearing. 

 

Summary of Contents for INLEM3





















Reviews: