Euromaid INLEM3 User Manual Download | Manualshive

Page: 6 / 20

background image

6

INSTALLATION (VENT OUTSIDE) Roof Cavity fan motor

Schematic diagram

1.

Connect the

Rangehood main body with the external cabinet by control wire, to

achieve power on and off, and also speed switching.

2. The control wire is separated into 3 parts, the first two parts are fixed onto the main

body and external cabinet, while the middle part is extension wire.

3. The Rangehood main body and the external cabinet will exhaust the smoke to

outdoor after installing the expansion pipe.

«
...
4
5
6
7
8
...
»

Summary of Contents for INLEM3





















Reviews:

No comments

Related manuals for INLEM3

Brand: S&P Pages: 54

Brand: Gaggenau Pages: 12

Brand: Broan Pages: 20

Brand: NEFF Pages: 16

Brand: V-ZUG Pages: 28

Brand: Hanseatic Pages: 48

Brand: Halton Pages: 10

Brand: Orbegozo Pages: 25

Brand: JUNO Pages: 16

Brand: Jenn-Air Pages: 4

Brand: Jenn-Air Pages: 34

Brand: FTK Pages: 12

Brand: Pelgrim Pages: 50

Brand: NEFF Pages: 12

Brand: NEFF Pages: 16

Brand: NEFF Pages: 84

Brand: ROBLIN Pages: 1

Brand: ROBLIN Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands