background image

 

  3    |   10 

 

 

Do  not  operate  the  charging  station  with  wet 
hands. 

 

The  charging  station  manufacturer  cannot  be 
made  liable  for  damage  or  injury  caused  by 
improper  handling,  installation,  or  use  of  the 
product. 

 

Any  usage  of  the  product  not  covered  in  this 
document is not allowed and could cause injury or 
death. 

BASE SPECIFICATIONS  

 

Input: 

230/400V~; 3W+N+PE; 50/60 Hz; 32A

max

 

 

Output: 

230/400V~; 3W+N+PE; 50/60 Hz; 32A

max

 

 

Maximum charging power: 

7.4 kW (1P), 22 kW (3P)

 

 

Device power consumption: 

from 1 W to 3 W 

Specification  of  frequency  bands  and  transmitting 
power (it is possible that not all modules are part of an 
actual device). 

LTE module

 

Frequency bands:  

LTE-FDD: B1 (2100 MHz), B3 

(1800 MHz), B5 (850 MHz), 

B7 (2600 MHz), B8 (900 

MHz), B20 (800 MHz) 

LTE-TDD: B38 (2600 MHz), 

B40 (2300 MHz), B41 (2500 

MHz) 

WCDMA: B1 (2100 MHz), B5 

(850 MHz), B8 (900 MHz) 

GSM/EDGE: B3 (1800 MHz), 

B8 (900 MHz) 

Transmitting power: 

33dBm±2dB for GSM 

24dBm+1/-3dB for WCDMA  

23dBm±2dB for LTE-FDD 

23dBm±2dB for LTE-TDD  

LTE Router  

Frequency bands: 

4G (LTE-FDD): B1 (2100 

MHz), B3 (1800 MHz), B5 

(850 MHz), B7 (2600 MHz), 

B8 (900 MHz), B20 (800 MHz) 

4G (LTE-TDD): B38 (2600 

MHz), B40 (2300 MHz), B41 

(2500 MHz) 

3G: B1 (2100 MHz), B5 (850 

MHz), B8 (900 MHz) 

2G: B3 (1800 MHz), B8 (900 

MHz) 

Transmitting power:  

21.9 dB

 

Wi-Fi module 

Frequency band:

  

2.4 - 2.4835 GHz

 

Transmitting power:

  

up to 15 dBm

 

RFID module

 

Frequency band:  

13.56 MHz (HF)

 

Transmitting power:  

up to 8 dBm 

Summary of Contents for INCH LITE













Reviews: