Etdoor ET-1000E Installation Instructions And User Manual Download | Manualshive

Page: 5 / 19

background image

Referring to Fig. 2 for recommended installation

1) Sectional door rail 5) O/S/C button

2) 24V DC flash light (optional extra) 6) Power socket

3) Wall switch 7) Door opener

4) Photo beam (RX/TX Type)

CHAIN SHUTTLE ASSEMBLY

As for the ease of the chain, it is delivered with the

chain and chain shuttle already assembled in the

track. If you need to assemble it yourself, connect

the chain shuttle to the chain with screw C tightened

firmly. Move shuttle B to half way along the rail

section; grease the chain and sprocket (Fig.3) with

a lithium type grease or equivalent. Do not use oil

type lubricants.

«
...
3
4
5
6
7
...
»

Summary of Contents for ET-1000E




















Reviews:

No comments

Related manuals for ET-1000E

Brand: Wayne-Dalton Pages: 18

Brand: CAB Pages: 40

Brand: Fabet Pages: 28

Brand: tau Pages: 40

Brand: E.T. Pages: 8

Brand: Chamberlain Pages: 40

Brand: DACE Pages: 22

Brand: tau Pages: 40

Brand: EasyWay Pages: 157

Brand: FAAC Pages: 13

Brand: CAME Pages: 24

RapidCoil RC300 Series

Brand: Raynor Pages: 39

Whisper Drive Security+ 47995D

Brand: Chamberlain Pages: 40

Brand: CAME Pages: 18

Brand: CAME Pages: 24

Brand: CAME Pages: 24

Brand: CAME Pages: 16

Brand: CAME Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands