TdA DKC1500 Series User Manual Download | Manualshive

Page: 1 / 13

background image

SLIDING GATE OPERATOR

USER’S MANUAL

MODEL: DKC1500/DKC1500Y

WARNING!

ONLY QUALIFIED AND EXPERIENCED TECHNICIANS

SHOULD ATTEMPT INSTALLATION OR SERVICE TO

THIS UNIT, OTHERWISE, SERIOUS PERSONAL

INJURY, DEATH, OR PROPERTY DAMAGE MAY

OCCUR.

PLEASE

KEEP

THESE

INSTRUCTIONS

FOR

FURTHER REFERENCE.

Total Door Automation (Australia) Pty Ltd

www.totaldoorautomation.com.au

[email protected]

1
2
3
...
»

Summary of Contents for DKC1500 Series














Reviews:

No comments

Related manuals for DKC1500 Series

Brand: B&D Pages: 24

MAST SLIM GMASTS05N0G00A

Brand: Comunello Automation Pages: 37

DARDO 424 e FOX 724

Brand: fadini Pages: 36

Brand: Key Automation Pages: 88

Brand: iSmarGate Pages: 29

Brand: SkyLink Pages: 2

Brand: DTS Pages: 12

Brand: NAS Pages: 19

Brand: Delton Pages: 8

AMICO Series A1824

Brand: CAME Pages: 12

Brand: SEA Pages: 36

Brand: HYDOM Pages: 12

Brand: Beninca Pages: 2

Brand: Beninca Pages: 14

Brand: CAMDEN Pages: 8

Brand: AutoGate Pages: 15

Brand: STEELON Pages: 33

Brand: Craftsman Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands