background image

ETC Installation Guide

ColorSource Spot V1.0

WARNING:

RISK OF ELECTRIC SHOCK! The light source in

this luminaire is not user-replaceable, and must be replaced
only by a qualified technician. Contact ETC Customer
Support for assistance.

AVERTISSEMENT :

RISQUE DE DÉCHARGE ÉLÉCTRIQUE! La

source lumineuse de ce projecteur n'est pas remplaçable
par l'utilisateur et ne doit être remplacée seulement par un
technicien qualifié. Contactez le service client ETC pour
obtenir de l’assistance.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should
always be followed including the following:

READ AND FOLLOW ALL SAFETY
INSTRUCTIONS

Do not use outdoors.

Do not let power supply cords touch hot
surfaces.

Do not mount near gas or electric
heaters.

Equipment should be mounted in
locations and at heights where it will not
readily be subjected to tampering by
unauthorized personnel.

The use of accessory
equipment not
recommended by the
manufacturer may cause
an unsafe condition.

Do not use this
equipment for other
than intended use.

SAVE THESE INSTRUCTIONS

The luminaire must be installed at
least 0.1 m (4.0 in) away from all
lighted objects.

Le luminaire doit être installé à au
moins 0,1 m (4,0 po) de tout objet
éclairé.

This product should not be
discarded as unsorted waste but
must be sent to separate collection
facilities for recovery and recycling.

Ce produit ne doit pas être jeté
avec les déchets ménagers mais
doit être déposé dans une collecte
de déchets électroniques ou dans
un point de collecte.

Protective earth (ground)

Protection Classe I Mise à la terre

ColorSource Spot V

Page 3 of 20

ETC

Summary of Contents for ColorSource Spot





















Reviews: