background image

32

www.eta.co.at

Up to software version X.35.X

ETAtouch controller

then pauses until 10:15 am , restarts at 10:15 am,
pauses from 10:20 am to 10:30 am , and so on ...
until the end of the time window at 2:00 pm .

In this operating mode, the circulation pump
can  also  start  outside  of  the  time  window

when hot water is being tapped. This is useful if, for
example,  the  time  window  ends  at  8:00  pm   and
you shower at 9:30 pm . When you then turn on the
hot water briefly, the circulation pump starts, and
you  will  have  hot  water  for  showering  shortly
afterwards. 
This runtime (outside the time window) is set in the
text  menu  (parameter  [Circulation  pump  delay]).
Enter  the  same  value  as  parameter  [Circulation
runtime].

Heat exchanger

The  tap  symbol  next  to  the  heat
exchanger  is  only  displayed  if  the  fresh
water module is feeding hot water into the
water  mains.  The  temperature  shown
next to this is the temperature of the hot
water currently being supplied.

If no hot water is being supplied, the heat exchanger is
shown blue all the way through.

Circulation pump in operation

Optional: for [Circulation pump]

The  pump  symbol  next  to  the  heat
exchanger  appears  when  the  circulation
pump for hot water is in operation.

Timer [Stand-by times]

This is only displayed if option [Target value can
be set with rotary knob] is deactivated 

This  timer  displays  the  set  charging  times  of  the
current day for charging the hot water tank. These time
windows are displayed as a black bar in the timer.

Timer [Circulation times]

This only appears if a circulation pump is installed
and the [Self-learning] function is deactivated.

This timer displays the set times of the current day to
operate the circulation pump. These time windows are
displayed as a black bar in the timer.

10.1.1.2

Operating modes

Ready

No hot water is currently being taken.

Working

Hot water is currently being supplied.

Buffer cold

Hot water is being supplied, but the buffer is not hot
enough to reach the configured hot water temperature.

Primary return too warm

Hot water is being supplied, but the selected hot water
temperature  is  being  reduced  because  the  [Primary
return] temperature in the heat exchanger of the fresh
water module is too high.

Malfunction

A temperature sensor in the fresh water module has a
defect.

Circulation

The circulation pump is in operation.

Venting

The controller has found air in the fresh water module
and  automatic  venting  is  in  operation.  For  this,  both
pumps are operated at full speed for a short period of
time  to  remove  the  air  from  the  fresh  water  module.
This can also take place multiple times sequentially.

Emergency operation

The  fresh  water  module  is  in  emergency  mode
because the admixing pump is defective. Currently, hot
water is being delivered but it is only being produced
with the buffer pump. 

Without  the  admixing  pump,  calcification
protection  of  the  heat  exchangers  it  not

guaranteed.  Protracted  emergency  mode  can
therefore calcify the heat exchanger.

Ready (Emergency operation)

The  fresh  water  module  is  in  emergency  mode
because the admixing pump is defective.

Without  the  admixing  pump,  calcification
protection  of  the  heat  exchangers  it  not

guaranteed.  Protracted  emergency  mode  can
therefore calcify the heat exchanger.

Circulation

Circulation pump delay

Summary of Contents for Fresh water module 33













































Reviews: