background image

6

www.eta.co.at

Read out node number

Preparation

2.2

Read out node number

Note down the node number of the defective
control panel

Reading the set node number is only required if
more than one control panel (BE-P) is present in

the system.

If several control panels are in the system, check the
set node number before removing the defective control
panel (if possible). Note it down so that the same node
number can be set after replacing. By default, the
boiler control panel always has the node number "0".
The following describes how the node numbers are
displayed on the different control panels.

Control panel "BE-P1" has a node switch on the
bottom.

Fig. 2-1: Node switch for "BE-P1"

From control panel "BE-P2", the node number is
only displayed in the ETAtouch control system.

Depending on the software version installed (up to
X.35.X or from X.36.0), the set node numbers are
displayed differently.

Up to software version X.35.X

On the control panel, press the 

 button and then

the [Software Version] button. The node number
set is displayed in the overview.

Fig. 2-2: Overview (up to X.35.X)

Software version X.36.0 and later

On the control panel, open the system settings 
and press the 

 [Version overview] button. The

node number set is displayed in the overview.

Fig. 2-3: Overview (from X.36.0)

2.3

meinETA remote control

Delete "meinETA" registration

If there is a registration for "meinETA" on the defective
control panel, this must be deleted before the
exchange (if possible). Note down the access details
for "meinETA" in order to register the new control panel
after the exchange. See chapter 

4.3 "meinETA remote

control"

.

Summary of Contents for BE-P3





















Reviews: