ESX VE 1000.1 Owner'S Manual Download Page 13

13

Balanced Inputs

Acoustic Phase Shift

Acoustic Phase Shift (APS)

of ESX

Balanced inputs have been used for many years in professional sound studios and high end home stereo systems. Unlike 

the unbalanced RCA's Balanced wires are insusceptible against interferences. But therefor an signal transmitter with 

specific wires is required. Ask your specialist dealer for the required equipment.

The ESX-VISION VE Series Amplifiers have an integrated Phaseshift Control. 

With the Phase Shift Control of the 

ESX VISION VE Series the stage's

acoustical center can be adjusted.

It is continously variable between 

0 - 180 degrees.

Band Pass - Function (Subsonicfilter)

By using the SUBSONICS FILTER you are able to adjust the lower threshold frequency of the subwoofer signal. The 

upper threshold frequency is controlled by the LOWPASS Control. Both filters together generate an spectrum which is 

called BAND PASS-SIGNAL. Now the frequency signal looks figurative like a trapeze which harmonize very well with an 

subwoofer enclosure and disturbing frequencies in the lowpass-range are limited.

SPECIAL FEATURES

Monoblock Amplifier VE1000.1 / VE1800.1

Summary of Contents for VE 1000.1





















Reviews: