ESAB A2 PEK Instruction Manual Download Page 62

Page: 62 / 74

10 TOOLS

0460 949 474

- 62 -

For LAF and TAF: 168 = Motor M1 (Wire feeder motor), 169 = Motor M2 (Travel motor).

Check the motor cables. Replace the pulse transducer.

169

A motor has stopped

There are no pulses from the motor pulse transducer.

For LAF and TAF: 168 = Motor M1 (Wire feeder motor), 169 = Motor M2 (Travel motor).

Check the motor cables. Replace the pulse transducer.

2310

Current servo saturation

The power source has temporarily delivered maximum current.

If the error persists, try lowering the weld data.

3205

High DC voltage

Check if the main voltage is too low or too high.

4201

High temperature

The power source has overheated. Welding is cancelled. Welding is permitted again when the
temperature falls below the maximum temperature parameter.

Check that the cooling air inlets or outlets are not obstructed or clogged with dirt.

Check the duty cycle being used, to make sure that the equipment is not being overloaded.

4202

High temperature

The power source has overheated. Welding is cancelled. Welding is permitted again when the
temperature falls below the maximum temperature parameter.

Check that the cooling air inlets or outlets are not obstructed or clogged with dirt.

Check the duty cycle being used, to make sure that the equipment is not being overloaded.

4203

High temperature

The power source has overheated. Welding is cancelled. Welding is permitted again when the
temperature falls below the maximum temperature parameter.

Check that the cooling air inlets or outlets are not obstructed or clogged with dirt.

Check the duty cycle being used, to make sure that the equipment is not being overloaded.

5010

High inductance

Inductance is too high, depending on long welding cables and/or high weld data.

Adjust the welding data.

8117

Lost contact with the unit

Lost contact with a unit.

Check wiring and the connector between the control unit and power source.

8411,
sub-
code 0

Wire speed motor error

A motor cannot maintain its speed. Welding stops.

Check that the wire feed has not jammed or runs too fast. If the error persists, send for a service
technician.

Summary of Contents for A2 PEK











































































Search results

Summary of Contents for A2 PEK

Reviews:

Related manuals for A2 PEK

Brands by name

Popular brands

ESAB A2 PEK, Instruction Manual

Search results

Summary of Contents for A2 PEK

Reviews:

Related manuals for A2 PEK

Brands by name

Popular brands