background image

                                                                                              

 2

  TABLE OF CONTENTS

SECTION

TITLE

PAGE

SAFETY

................................................................................................................................ 3

1

DESCRIPTION ........................................................................................................................ 9

2

INSTALLATION ..................................................................................................................... 10

3

OPERATION ......................................................................................................................... 13

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and

accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance with the
instructions provided. This equipment must be checked periodically. Defective equipment should not be used.
Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such
repair or replacement become necessary, the manufacturer recommends that a telephone or written request
for service advice be made to the Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.

The user of this equipment shall have the sole responsibility for any malfunction which results from improper
use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a
service facility designated by the manufacturer.

Summary of Contents for 0558001912

















Reviews: