ERNITEC 1504M Instructions Manual Download Page 7

Page: 7 / 16

Operation of telemetry receivers

This section will describe operation telemetry receivers directly from the 1504M keyboard.

Select Camera

If Camera 3 is to be controlled:

Select camera number 3

All subsequent operations are now directed to camera 3 until a new camera is
selected.

Select all cameras (broadcast)

If all cameras should be operated simultaneously, press:

Broadcast commands

Warning:

When e.g. activating the pan functions all cameras will pan! The broadcast function

should therefore be used with care!

Zoom

Change the focal length:

Joystick

Zoom wide

Zoom narrow

Focus

If the picture on the selected monitor is not in focus, press:

Focus near

Focus far

Iris

If the picture on the monitor is too dark or light, press:

Iris open

Iris close

Note: Available only if supported by the connected equipment.

1504M E-Mux & PTZ control

2821-00062

Page 7

Summary of Contents for 1504M

















Search results

Summary of Contents for 1504M

Reviews:

Related manuals for 1504M

Brands by name

Popular brands

ERNITEC 1504M, Instructions Manual

Search results

Summary of Contents for 1504M

Reviews:

Related manuals for 1504M

Brands by name

Popular brands