manualshive.com logo in svg

Ergoswiss 901.20024, Operating Instruction

Share
Download
Ergoswiss 901.20024 Operating Instruction Download Page 10

 

 

 

 

 

 

 

Operating Instruction 

Spindle lifting system SL/SM compact

 

 

 

Document no.: B-00061 

Edition 2018 02

 

operating instruction EN 

Copyright by Ergoswiss AG

 

10/23 

 

3.2

 

Mounting of the manual control switch 

3.2.1

 

Manual control switch Up / Down Front 

 

1.

 

Position the manual control switch at the desired loca-
tion underneath the table top.  

The front edge of the manual control switch should not 
stick out of the edge of the table. 

 

2.

 

Fasten the manual control switch using the mounting 
screws. 
Be careful not to drill through the table top! 

 

 

 

 

 

3.2.2

 

Manual control switch Up / Down Touch 

 

1.

 

Position the manual control switch at the desired loca-
tion underneath the table top.  

The front edge of the manual control switch should 

not stick out of the edge of the table. 

 

2.

 

Fasten the manual control switch using the mounting 
screws. 

Be careful not to drill through the table top! 

 

 

 

 

Summary of Contents for 901.20024
























Reviews:

No comments

Brands by name

Popular brands

Load more brands